118
使用 Mrtg 監控 squid
今天花了一上午的時間,總算做成了Mrtg對Squid的監控.我把我的配置過程貼出來.希望對大家有幫助
(1)我們需要修改squid
vi /etc/squid/squid.conf
acl snmppublic snmp_community public (設置snmp監控的共同體為public)
snmp_port 3401(設置snmp監控端口)
snmp_access allow snmppublic all(允許所有的計算機訪問snmppublic)
然後從新啟動squid /etc/rc.d/init.d/squid restart
(2)把/etc/squid/mib.txt 複製到/etc/mrtg/squid.mib
cp /etc/squid/mib.txt /etc/mrtg/squid.mib
(3)然後修改/etc/mrtg/mrtg.cfg
加入LoadMIBs: /etc/mrtg/squid.mib
(4)在/etc/mrtg/mrtg.cfg加入如下
Target[proxy-hit]: cacheHttpHits&cacheServerRequests:public@x.x.x.x:3401(x.x.x.x為你機器的IP地址)
MaxBytes[proxy-hit]: 100000
Title[proxy-hit]: HTTP Hits
PageTop[proxy-hit]: <H1>;proxy Cache Statistics: HTTP Hits/Requests</H1>;
<TABLE>;
<TR>;<TD>;System:</TD>;<TD>;redhat.grandunion.com.cn</TD>;</TR>;
<TR>;<TD>;Maintainer:</TD>;<TD>;Serassio Guido</TD>;</TR>;
<TR>;<TD>;Description:</TD>;<TD>;Squid Proxy server</TD>;</TR>;
</TABLE>;
Suppress[proxy-hit]: y
LegendI[proxy-hit]: HTTP hits
LegendO[proxy-hit]: HTTP requests
Legend1[proxy-hit]: HTTP hits
Legend2[proxy-hit]: HTTP requests
YLegend[proxy-hit]: perminute
ShortLegend[proxy-hit]: req/min
Options[proxy-hit]: nopercent, perminute, dorelpercent, unknaszero
Target[proxy-srvkbinout]: cacheServerInKb&cacheServerOutKb:public@x.x.x.x:3401(x.x.x.x為你機器的IP地址)
MaxBytes[proxy-srvkbinout]: 2000(這兒為你的真實網絡帶寬xxxK)
Title[proxy-srvkbinout]: Cache Server Traffic In/Out
PageTop[proxy-srvkbinout]: <H1>;Cache Statistics: Server traffic volume (In/Out)</H1>;
<TABLE>;
<TR>;<TD>;System:</TD>;<TD>;redhat.grandunion.com.cn</TD>;</TR>;
<TR>;<TD>;Maintainer:</TD>;<TD>;Serassio Guido</TD>;</TR>;
<TR>;<TD>;Description:</TD>;<TD>;Squid Proxy server</TD>;</TR>;
</TABLE>;
Suppress[proxy-srvkbinout]: y
LegendI[proxy-srvkbinout]: Traffic In
LegendO[proxy-srvkbinout]: Traffic Out
Legend1[proxy-srvkbinout]: Traffic In
Legend2[proxy-srvkbinout]: Traffic Out
YLegend[proxy-srvkbinout]: per minute
ShortLegend[proxy-srvkbinout]: b/min
kMG[proxy-srvkbinout]: k,M,G,T
kilo[proxy-srvkbinout]: 1024
Options[proxy-srvkbinout]: nopercent, perminute, unknaszero
保存文件,並運行mrtg mrtg.cfg
然後運行indexmaker mrtg.cfg >; /var/www/mrtg/index.hmtl
這樣你就可是隨時監控你的SQUID運行情況
後記:使用mrtg也可以監控cpu load disk等等,可以參考
https://www.leeshow.com/?v=soft&s_v=linux&s_s_v=&art_id=108
這樣你就可以對Squid進行全麵的監控…!
:em02:
snmp_port 3401
acl snmppublic snmp_community pc109237
snmp_access allow snmppublic all
proxy -v 2c -c pc109237 localhost:3401 .1.3.6.1.4.1.3495.1
最後更新：2017-01-04 22:34:31